Latest Verified & Correct BICSI INSTC_V8 Questions & Answers Daily Updated
100% Pass Guaranteed Download Cabling Installation Exam PDF Q&A
NEW QUESTION # 58
Which of the following combinations is used to identify the tip conductors in Pair 1 of a 4-pair cable?
- A. Green-White
- B. Brown-White
- C. White-Orange
- D. White-Blue
Answer: D
NEW QUESTION # 59
If the specified diameter for a conduit run is 25 mm (1 in), but an installer only has 20 mm (¾ in) conduit available, what is the MOST appropriate BICSI-recommended solution?
- A. Obtain the specified 25 mm conduit or larger
- B. Combine multiple 20 mm conduits side-by-side
- C. Increase the tension while pulling to fit cables into the 20 mm conduit
- D. Use the 20 mm conduit but reduce the cable count
Answer: A
NEW QUESTION # 60
What is the primary purpose of the telecommunications bonding infrastructure?
- A. Provide backup power to the telecommunications equipment when primary power to the equipment fails.
- B. Equalize potentials between metallic surfaces and equipment within entrance facilities
- C. Improve the performance of the installed telecommunications equipment
Answer: B
NEW QUESTION # 61
You are pre-terminating cable. Where should the labels be placed?
- A. Near end
- B. Far end
- C. Both ends
Answer: C
NEW QUESTION # 62
What is the recommended minimum amount of aisle space between and around equipment?
- A. 0.6 m (2')
- B. 1.2 m (4')
- C. 1 m (3.3')
- D. 1.52 m (5')
Answer: C
NEW QUESTION # 63
When labeling patch panels, which of the following is MOST aligned with TIA-606 and BICSI best practices?
- A. Only label the left-most and right-most ports
- B. Assign labels based on random color coding for each port
- C. Label each port sequentially by row (e.g., 1-24, then 25-48, etc.)
- D. Use building zone references, omitting port identifiers
Answer: C
NEW QUESTION # 64
Light pulses in optical fiber cables are subjected to a loss in power as the light pulses travel along the optical fiber. Which of the following terms is used to describe this phenomenon?
- A. Grounding
- B. Attenuation
- C. Crosstalk
- D. Frequency
Answer: B
NEW QUESTION # 65
A BICSI Installer 2 is tasked with installing optical fiber from the Main Equipment Room (MER) to a Satellite Telecommunications Room. Which factor below is MOST critical to ensure the fiber's long-term reliability?
- A. That the cable is installed in metallic conduit only
- B. That the fiber is tested with an OLTS and labeled before installation
- C. That the maximum pulling tension and minimum bend radius specifications from the manufacturer are maintained throughout the route
- D. That the fiber is color-coded orange for multi-mode or yellow for single-mode
Answer: C
NEW QUESTION # 66
Electrical power (P) is measured in ___________?
- A. Farads
- B. henries
- C. Watts
- D. Ohms
Answer: C
NEW QUESTION # 67
Which of the following is the first step of the emergency rescue process?
- A. Contact 911
- B. Notify someone
- C. Survey the scene
- D. Secure the area
Answer: C
NEW QUESTION # 68
A purple backboard should be used to identify ________?
- A. Demarcation point
- B. Horizontal cable
- C. Network connections
- D. Common equipment
Answer: D
NEW QUESTION # 69
How much cable slack should be left in the work area after termination?
- A. 0.5m (1.6')
- B. 1.2 m (4')
- C. 1m (3.3')
- D. 3m (10')
Answer: C
NEW QUESTION # 70
You are terminating a category 3 cable. What is the maximum permissible amount of untwisting?
- A. 100 mm (4")
- B. 25 mm (1")
- C. 75 mm (3")
- D. 38 mm (1.5")
Answer: C
NEW QUESTION # 71
What is the minimum inside bend radius for balanced twisted pair (4 pair) cable?
- A. 4 times the outside cable diameter
- B. 25 mm (1")
- C. 50 mm (2")
- D. 15 times the outside cable diameter
Answer: A
NEW QUESTION # 72
When terminating fiber connectors, which factor MOST influences the achievable insertion loss?
- A. The labeling scheme
- B. The color of the fiber jacket
- C. The length of the fanout kit
- D. The polishing technique and end-face quality
Answer: D
NEW QUESTION # 73
Which type of optical fiber cable should be color coded with an Orange outer cable sheath?
- A. SM optical fiber
- B. Polarization maintain SM optical fiber
- C. Dispersion-shifted SM optical fiber
- D. MM with a 100 um core diameter
Answer: D
NEW QUESTION # 74
Which topology uses a linear configuration that places all network devices on one length of cable?
- A. Ring
- B. Bus
- C. Star
Answer: B
NEW QUESTION # 75
Which of the following make the biggest impression on a customer during face-to-face conversation?
- A. Body language
- B. Tone of voice
- C. Choice of words
Answer: A
NEW QUESTION # 76
What is the maximum number of work areas that a CP should serve?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION # 77
Which of the following is the bonding connection point for telecommunications systems and equipment in the area by a telecommunication space?
- A. RBB
- B. TEBC
- C. SBB
- D. BBC
Answer: C
NEW QUESTION # 78
Which of the following tend to cause sheath damage during cable pulling?
- A. EMT/ENT
- B. RMC/IMC
- C. FMC/FMT
Answer: C
NEW QUESTION # 79
What method of transmission is used to transmit signals during a telephone call?
- A. Simplex
- B. Full duplex
- C. Half-duplex
Answer: B
NEW QUESTION # 80
Which of the following quantifies the bandwidth of a cabling system in a frequency range of interest?
- A. Megabits
- B. Megahertz
- C. Kilowatt hours
- D. Volt-amperes
Answer: B
NEW QUESTION # 81
A cross-connect in the Telecommunications Room uses 110-blocks. Which parameter is MOST important to verify after performing cross-connects?
- A. A 25 mm (1 in) cable slack behind the block
- B. That block label colors match the TIA standard
- C. The block's brand matches the cable manufacturer
- D. Continuity and wire map for each pair
Answer: D
NEW QUESTION # 82
......
INSTC_V8 PDF Dumps Are Helpful To produce Your Dreams Correct QA's: https://braindumps2go.actualpdf.com/INSTC_V8-real-questions.html
